#AUTODESK 123D DESIGN MANUAL PDF INSTALL#
#AUTODESK 123D DESIGN MANUAL PDF ANDROID#
#AUTODESK 123D DESIGN MANUAL PDF SOFTWARE#
#AUTODESK 123D DESIGN MANUAL PDF CODE#
#AUTODESK 123D DESIGN MANUAL PDF BLUETOOTH#

#AUTODESK 123D DESIGN MANUAL PDF SOFTWARE#

With the increasing engineering trends, people are always looking for software that lets them design CAD models and draw illustrations without implicating practicality. In this DIY kit, we use KS0173 keyestudio Nano ch340, you could refer to.

#AUTODESK 123D DESIGN MANUAL PDF BLUETOOTH#

When using, as long as the Bluetooth module is not involved, these two product kits can use the common source code.Д¬heck relevant info of frog robot kit from the link:

#AUTODESK 123D DESIGN MANUAL PDF ANDROID#

But frog robot kit contains a HM-10 Bluetooth module, compatible with both Android and iOS phone. This OTTO kit contains a HC-06 Bluetooth module, using Bluetooth 2.0, only compatible with Android phone. This OTTO kit is similar to Keyestudio Frog Robot for Arduino Graphical Programming kit(KS0446). Include all main moves very easy to adjust speed, number of times and direction. You can always try different codes from the same Github repository to use the ultrasound to avoid obstacles or detect objects and the buzzer to make sounds.

#AUTODESK 123D DESIGN MANUAL PDF CODE#

Finally open OTTO_smooth_criminal.ino code and upload to your Arduino Nano for dancing Otto mode.ДҐ.Try OTTO_avoid.ino for obstacle avoidance

#AUTODESK 123D DESIGN MANUAL PDF INSTALL#

Connect your Otto through USB (your computer should install the drivers)Д¤. Copy all libraries to C:/Users/user/Documents/Arduino/libraries (or wherever your library folder is installed)ДЈ. Download and install Arduino softwareIDE:Дў. The Head has snap feature, take care of the cables and close it. The jumper wires are Not Included in the kit list.Дў.When connecting well all the components and uploading the code, CANNOT press the button welded to battery case, that is, CANNOT supply the power otherwise, code upload fails. Or else, the space is not enough, should connect the Bluetooth module to the shield with male-to-female jumper wires. Then follow the diagram pins numbers and make sure to put them in the right position.ДЎ.When connecting the Bluetooth module, CANNOT directly plug into the shield. Prepare the jumper cables, buzzer, and switch. Insert diagonally the both boards together facing the USB conector to the hole in the 3D printed head, then use the pointed screws to fix it. Then put the Arduino nano in the shield, optionally you can weld the positive cable of battery holder to Vin in the board and negative cable to any GND. Start from the ultrasound sensor is important to pull out the eyes to the limit. Once they are in right position, use the pointed screws to fix them from the back. Taking care of the cables as showed in the illustration, you should put the cables inside the slots of the body passing through the hole of the legs. Take the other 2 micro servos put them in the defined locations in the 3D printed body, and fix them only with screws.Д¬onnect the legs to the hub of the micro servo, important like the foot servos, you must check the legs are able to rotate 180 degrees each side respect to the body.ДЄfter verifying the alignment, fix them using the small screws to the hole inside the leg. Is very important to check that the servo is able to rotate at 180 degrees to each side.ДЄfter checking the movement, use only the small screw to fix it. Put the micro servo inside feet and then push it inside, if is to hard maybe need to clean more the area with a cutter. OTTO-DIY-Instruction-Manual Step2: Foot Servos Assembly You can print individually piece by piece to match the colors of the original design or optionally print all at the same time in an area of 14cm x 14cm.ДЇor slicing and generating the g code for the machine free slicer software like Cura or FlashPrintthat comes with the FlashForge Finder 3D printer that we are using (If you are outsourcing the printing, no need to worry about it)ДЄfter printing, you will need to clean a little bit the legs and feet areas that fix the motors.Д«uild Your Own Otto Robot Step1: Check Your Parts From Bottom to Top

Recommended to use a FDM 3D printer with PLA material.

Otto is very well designed for 3D printing, so wonвЂ™t give you trouble if you follow this common parameters:

If you do not have a 3d printer, you can always use services like or local maker spaces. The kit includes everything you need to build your Otto in 1 hour: NO SOLDERING REQUIRED!ДЄnd then you only need to 3D print 6 parts in total:ДЇor the 3D printing parts, you can print them out with 3D printer. You are able to modify it or even recreate them to make you own Otto robot and then share to the world!

No need technical knowledge, perfect for beginners. Otto is designed using Autodesk 123D Design software.

The shelf parts are designed using 3D printer, simple electronics connections (almost no welding required), and basic coding skills. His small body is in the assembled size, with simple structure. Otto is able to walk, dance, make sounds and avoid obstacles.

Otto is an interactive robot that anyone can make! It is completely open source, Arduino compatible and 3D printable.

5.1 Step1: Check Your Parts From Bottom to Top.

Autodesk 123d design manual pdf